# Building the Root 2 CNC Multitool Router/Bill of Materials and Estimated Costs

Most of these parts can be cheaply found on ebay if you search around a little bit. Be aware that if you order parts from Hong Kong or China there will likely be a wait time of 1 or 2 months for the part to arrive. US sellers will cost slightly more but are useful if you are part way through the build and need that part right way. Otherwise a good approach is to just buy the parts ahead of time a little at a time so that about the time you need them they arrive. Keep an eye out for any coupons or sales ebay has. High cost items like the spindle or stepper motors could be bought for a nice discount.

## Plastic Parts

editName | Axis | Quanity |
---|---|---|

Root 2 CNC - Y gantry assm-1 Y-Axis Belt Clamp GT2 | Y | 2 |

Root 2 CNC - Y gantry assm-1 Y Motion Bearing Mount | Y | 4 |

Root 2 CNC - Y gantry assm-1 Y Drag Chain Carriage | Y | 1 |

Root 2 CNC - Y gantry assm-1 X-Axis Carriage Y Drag Chain Mount | Y | 1 |

Root 2 CNC - Y gantry assm-1 X-Axis Carriage Y Drag Chain Mount Idler | Y | 1 |

Root 2 CNC - Y gantry assm-1 X-Axis Belt Clamp | Y | 2 |

Root 2 CNC - Y gantry assm-1 X-Axis Box Bar Mount | Y | 2 |

Root 2 CNC - Y gantry assm-1 Dirt Cover | Y | 2 |

Root 2 CNC - X carriage-1 Z-Axis Motor Mount | X | 1 |

Root 2 CNC - X carriage-1 Z carriage-1 Spindle Upper Clamp | X | 1 |

Root 2 CNC - X carriage-1 Z carriage-1 Spindle Lower Clamp | X | 1 |

Root 2 CNC - X carriage-1 X-Axis Motor Mount | X | 1 |

Root 2 CNC - X carriage-1 X-Axis Carriage Drag Chain Mount Idler | X | 1 |

Root 2 CNC - X carriage-1 linear rail 90 bearing mount Y-Axis Carriage | X | 2 |

Root 2 CNC - X carriage-1 3M Pulley 32T 5mm | X | 1 |

Root 2 CNC - X carriage-1 3M Pulley 22T 8mm | X | 1 |

Root 2 CNC - Ramps controller-1 Ramps Case Lid | 1 | |

Root 2 CNC - Ramps controller-1 Ramps Case Base | 1 | |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Bar Mount | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Bar Mount Idler | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Bar Mount Idler Mirror | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Bar Mount Mirror | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Motor Mount | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Motor Mount Mirror | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 Y-Axis Drag Chain | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 3M Pulley 48T 8mm | Y | 1 |

Root 2 CNC - Base and Y axis assm-1 3M Pulley 24T 5mm | Y | 1 |

Root 2 CNC - Base and Y axis assm- Foot | Y | 4 |

## Electronics

editName | Amount | Estimated Cost | Comments |
---|---|---|---|

Arduino Mega | 1 | $10.95 - $46 | Non-genuine Arduino is cheaper but I am still unsure of the quality versus a real one |

Ramps 1.4 | 1 | $7.57 | Ebay and Amazon give many options. These can be pre-built or even kits that you can assemble yourself. |

DRV8825 (Optional but preferred over the A4988) | 3 | $4.74 | |

Nema 17 Stepper motors (Get the Highest torque possible) | 3 | $57 | Users have reported success with the 17HS19-2004S1 model from ebay number 231427537485 by the user account stepperonline |

60mm DC Fan | 1 | ||

Endstop micro switches (KW11 I drilled the whole to 3mm to screw then in to the plastic parts) | 6 | $1.26 | These are cheaply found on ebay |

DC Spindle (52mm Diameter - Get the highest wattage, you will be thank full later on) | 1 | ||

Diode This is needed if using the heatbed Mosfet on the ramps to control the spindle - google Mosfet switching inductive loads for more information | 1 | ||

4 core AWG26 cable (use for motor wiring and endstops) | $9.84 |

Total estimated cost: $91.09

## Fixings

editIt seems to make sense for some of the items to just buy a 100 pack of them. This way you know you will have enough and also it can help build up your supplies for these parts. Ebay or Amazon are good sources for most of these parts. Local hardware stores may also have these items, however, those prices tend to be higher than can be found online. Some of the prices below are the price to buy a few extra parts for example I bought 30 M8 Tee Nuts for $3.99 but I only needed 16 of them.

Name | Amount | Estimated Cost | Comments |
---|---|---|---|

M8 nuts | 100 | $5 | |

M8x25 bolts | 24 | $9.99 | These bolts are used to:
Attach the bearings to the Y Motion Bearing Mount |

M3 nuts | 100 | $3.99 | |

M4 nuts | 100 | $4.99 | |

M3 washers | 100 | $2.24 | |

M4 Washers | 100 | $2.60 | |

M8 washers | 100 | $5.29 | |

M8 Tee Nuts | 16 | $3.99 | |

M3 9mm Penny Washers | 100 | $5.94 | |

M8 80mm bolt | 10 | $15.68 | These are used to clamp the Y Motion Bearing Mounts together. Threaded rod can also be used. |

M3x30 bolt | 100 | $9.94 | These seem to about the right length for attaching the Y axis mounts to the base. Different size may be needed based on the thickness of the baseboard. |

## Bearings

editName | Amount | Estimated Cost | Comments |
---|---|---|---|

608 Bearings | 36 | ||

LM10UU | 4 |

## Metal Work

editName | Amount | Estimated Cost | Comments |
---|---|---|---|

Aluminum Box section (X-Axis and Y-Axis) 25x25x496x3mm (W,D,L,T) | 4 | $14 | Online this was costing a lot, but a local shops did seem to have it for a lot cheaper. |

M8 Smooth Rod 580mm | 1 | ||

M8 Threaded Rod 85 mm | 8 | ||

M8 Threaded Rod 500 mm | 1 | ||

M8 Threaded Rod 200 mm | 2 | ||

M8 Threaded Rod 230 mm | 1 | ||

M8 Threaded Rod 100 mm | 2 | ||

M10 Smooth Rod 185 mm | 2 |

## Motion

editName | Amount | Estimated Cost | Comments |
---|---|---|---|

GT2 Belt (Length depending on size of the machine) | 1 | ||

GT2 36T Pulley 8mm Bore | 2 | ||

3M-210T-06 Belt | 1 | $4.25 a piece | Used to drive the Y-axis. If using two motors on the Y-axis then you will need two of them. Searching for 210-3M-06 on ebay turns up results. |

3M-264T-06 HTD | 1 | ||

GT2 16T Pulley 5mm Bore | 1 | ||

Drag Chain 20 x 10 mm 1m Length | 2 |

## Wood

edit- 2x Wood Side Panel
- 1x Wood Base